Heating: Crystal Vortex™ Torus Tower for Underfloor & Heating Circuit | Whole-House Vortex System Level 1 | 4

Our Aquadea water filters remove 95% of active chlorine, benzene, pesticides, heavy metals (lead, uranium) and much more.

For more information on contaminant retention: please click here

That depends on the water filter. First, the versions for Ukato/Okato:

Solo - change every six months: K7B or Aquadea - Q1 / with 0.1 micrometer germ barrier

Duo - following the direction of flow, every six months: K7 or
Aquadea - Q8; every six months: K7B or Aquadea - Q1 / with 0.1
micrometer germ barrier

Trio - following the direction of flow, every six months: K7 or
Aquadea - Q8; every six months: K7 or Aquadea - Q8; middle
filter cartridge annually; K7B or Aquadea - Q1 every six months / with 0.1 micrometer germ barrier

Quattro - following the direction of flow, every six months: K2 or
Aquadea - Q3; every six months: K7 or Aquadea - Q8; annually: K7 or
Aquadea - Q8; every six months: K7B or Aquadea - Q1 / with 0.1
micrometer germ barrier;

Depending on the model, please turn off the water before changing the filter.

Both water filter units deliver the same performance, as they use the same
filter cartridge.

The difference lies first of all in the design. The Okato Nature water filter has a wooden head and a wooden base, is more solid, has a longer, thicker spout and a wider base.

The Okato Style water filter has a plastic head and a narrower base. Its spout is thinner and shorter. Overall it is smaller and lighter, which is an advantage when traveling, in a motorhome or in small kitchens.

The Okato Nature water filter, on the other hand, is well suited for use with multi-level vortexers or with kitchen sinks that have a very wide rim.

To purify water on a material level, you need a water filter.

Aquadea® water vortexers cleanse the water of all unwanted
information and restore its dynamism and natural form.
(Hexagonal structures, the vortex dynamics of a mountain stream, vitality)

Information on the Aquadea Crystal Vortex™ chamber technology

Yes, Aquadea water filters also remove medication residues.
The filtration performance here lies between 82% and 98%.

As a general rule, let the water run until it comes out cool (the same temperature as straight from the tap); depending on the type of filter, this can be up to 10 liters. If you are away for 3–4 weeks or longer, the cartridges can be stored in the refrigerator. This means: for under-sink versions, shut off the water supply, remove the cartridges by unscrewing them, wrap them airtight in plastic wrap and place them in the refrigerator. The cartridges can be stored there for up to four months and then used again. The filter change interval is then extended by the storage period.

The following link takes you to the filter replacement instructions:

DOWNLOAD

Yes, our countertop water filters also work at low pressure.
The lower the pressure, the longer it takes for the water to run through the unit.

Aquadea® vortex chambers cleanse the water of all unwanted information and restore its dynamism and natural form. (Hexagonal structures, the vortex dynamics of a mountain stream, vitality)

https://aquadea.store/pages/kristallwirbel-technologie

All our products have an M22 female thread.
So you need an M22 male thread connection on your faucet.
If your faucet has a different thread, we offer numerous adapters to connect your thread to our water vortexers or to the “Okato” countertop filter.

The ToneOne has one implosion vortex chamber, so its flow rate is reduced to approx. 3.8 l per minute. The Trinity has three implosion vortex chambers, and its flow rate is approx. 11.4 l per minute. This naturally depends on the water pressure at the tap.

To purify water on a material level, you need a water filter.

The water vortexer purifies the water on an energetic level.

Warranty and care of AQUADEA water vortex chambers

We at AQUADEA offer a 2-year warranty on our product. With
electroplated resonance plates such as silver, gold, ruthenium, platinum, palladium and
rhodium, it is always possible that the metal coating becomes damaged after prolonged use and the base plate of bronze or titanium becomes visible. This does not change the energetic effect in any way. In the case of a manufacturing defect, we can identify this and offer a replacement under the warranty. However, if the product has not been cared for, you must expect not to receive a refund in the event of damage. Even so, please contact us immediately in the case of self-inflicted damage as well, so that we can quickly find a solution together. To keep it from coming to that in the first place, read the individual care steps here so that you can preserve the quality of the products as far as possible – after all, signs of use such as light scratches are completely normal.

Care step by step

Step 1: Descaling with citric acid

As the basis of every cleaning, you should first remove limescale from the product. Depending on the lime content in the different regions, you will need to do this at different intervals, which is why we cannot give a general recommendation here. However, you should check every few weeks whether it is time again. The more regularly this is done, the easier and quicker the cleaning will be.

First unscrew your Trinity or ToneOne and any combinations
or unscrew the shower plate from the bell. Take a
glass bowl, fill it about 5cm high with warm water (about 200-400mL),
add one teaspoon of pure citric acid (e.g. HEITMANN) and stir briefly. Leave the products in the water for 5-15 minutes, depending on how dirty they are. Then rinse with clear water.

Important! Do not use acetic acid, vinegar essences, vinegar-based products or any other cleaning agents, as these attack or even destroy the metals and the crystals.

Caution! In products with calcareous stones such as Larimar, lapis lazuli and azurite-malachite, the gemstones dissolve in citric acid. If you place only the resonance plate of a shower in the water with citric acid, you can still clean the plate. Make sure you fill the bowl with only 1cm of water so that the resonance plate is in contact with it, but not the calcareous stone.

Tip! To avoid limescale deposits from standing water, we recommend patting the bundle nozzle dry once a day, or the shower plate after showering, with a
clean, soft cotton cloth that is as dust-free as possible. To remove the water from the shower hose with a single click, we also offer a Nito plug-in connector in our shop.

Note for bronze products: Pure bronze products, as well as bronze products with damaged electroplating, may develop a green oxidation that looks very similar to verdigris. Verdigris, however, only forms through contact with vinegar.

Step 2: Cleaning with Hagerty Silver & Multimetal foam

Metals can oxidize, and in addition to limescale this can lead to further soiling. For this purpose there is the Silver & Multimetal Foam by Hagerty. Using the enclosed sponge, carefully dab on the foam until it lathers. Let it work until it has dried on, then rinse the foam off with the sponge under running water. This foam is suitable for all metals and is normally sufficient with regular care.

Step 3: Cleaning with metal-specific cleaning agents

With insufficient care, or sometimes depending on the regional water quality, heavier soiling may occur that then requires more intensive care.

For silver and the metals ruthenium, platinum, palladium and rhodium, we recommend Hagerty Silver Polish. You can carefully dab on the polish with a cotton swab or cotton pad. Let it work until it has dried on. Wash off the polish under running water with a very soft sponge or cloth.

For gold, which may develop brownish spots under certain circumstances, Hagerty offers its so-called Gold Clean. To use it, first immerse the product in the
liquid if its size allows. Afterwards, you can additionally
clean the oxidized areas with circular movements using a soft cloth previously dipped in the liquid. If you are cleaning a shower plate, you can skip the first step and polish the plate directly with the soaked cloth.

For bronze, which is particularly susceptible, there is likewise Hagerty Copper, Brass & Bronze Polish. Bronze is robust, which is why you can apply somewhat more pressure here than with electroplated products. Apply the polish, let it work until it has dried on, and then rinse it off with a soft sponge under running water.

If you have further questions about proper care or are unsure which
care product is best suited to your product, send us an email at vertrieb@aquadea.de or call us at 08135 - 99 474 55.

All Hagerty products mentioned are available in our shop.

For an overview of our Hagerty products, click here.

Your AQUADEA team

All our products have an M22 female thread. So you need an M22 male thread connection on your faucet. If your faucet has a different thread, we offer numerous adapters to connect your thread to our water vortexers or to the “Okato” countertop filter.

Trinity from 1.5 bar
Tone One from 1 bar

Vortexing also takes place at lower pressure, but it is not as strong.